Aluminum Alloy Chipset Heatsinks for PC Memory Chips (8-HSK Set)

Pros: Double Sided thermal tape which is super sticky!
Perfect Size for DDR2 / GDDR2/3 memory on graphics's cards
I also found there great for all sorts of chips, I Have applied some to all my Motherboard chips, my PCI Card device chips too.
This could also be used in consoles too like Xbox 360, Xbox, Playstation's to help keep the temps down, While it wont prevent a RRoD as that is a issue neer the Xbox CPU but still should help some :D
Seems to conduct heat well enough as they get warm :D

Cons: they could be a little taller id suppose

Other: Ill be ordering another 5 Packs of these babies to apply them to 2 other pc's and some consoles :D

Pros: It's small and it fits right were I needed it to be. It does the job as for the heat dissipation.

Cons: None I can see. Maybe a little small for the application I do with it. Maybe that the design could be better with higher fins...but anyway....does the job as is.

Other: I would like DX to have more size aviable of those heat sink. That's the kind of tings that really helps cooling down any small device. Just get it if you need it.

Pros: - Fits perfect on the ram chips of a Geforce 7600 GT.
- Increases general cooling of the graphics card.

Cons: - It's fiddly to pull the cover of from the sticky pads.
- Just a heat conductive pad.

Other: I bought this for the constantly overheating Geforce of my Dads PC and now everything is fine. I am not sure if you lose warranty when using this, because of modifiying the hardware.

Pros: + These are very cheap!
+ If they could stick, they would probably cool nicely

Cons: - The thermal tape that comes with it is ridiculously bad. It wouldn't stick to hot glue.
- Could do with slightly higher fins and a thinner base to increase surface area.
- Did I mention the thermal tape?

Other: If you have some proper thermal glue, get'em. They're cheap and I believe they will cool whatever you stick them to pretty well. I'm considering buying more of them to use in a DIY cooling project.

Pros: - Fits perfectly on GEForce 8600GT ram chips.
- Ready to use, just open the package, take out the protection tape and paste it.
- Nice thermal efficiency.
- No other place sells it for such a low price.

Cons: - No cons, maybe it should be a little taller to enhance dissipation.
- Could be copper made, would buy it even if it was a little more expensive.

Other: Buy it, best choice for the price.
Buy it, best choice for the price.
Buy it, best choice for the price.

Pros: great little heatsinks that can be used on video card memory chips, computer memory (if you have enough space between memory slots), and on motherboard mosfet. im using them on a gigabyte 965p motherboard to cool the mosfet. cant actually measure the performance of them, but im sure they do something good.

Cons: they arent copper, but they do the job for the price. maybe dx should have bulk packs of these things. you need to push the heatsinks onto the chips with some force so that the tape sticks on or else it will fall off.

Other: good for mosfets, motherboard chips, video card memory chips, and ram.

Pros: I used in my video card, it was perfect, the price very good too, unfortunately finding the product was only over $ 5
I loved the product

Cons: nothing, nothing against the product, the product is good for the price it is sold

Other: wire everything perfect in the purchase, the product served me well in moomento, I think I might have to sell new colors and sizes

Pros: I've had this for over 2 months and it seems to be working perfectly. Not that hard to install. You just peel the protective film/tape and stick it on to your chip. So far, it's holding up fine and it's keeping everything running without a hitch.

Cons: Nothing that I can think of. Price could be a bit cheaper, I suppose.

Other: Looked everywhere else for this and if you calculate the shipping costs with other online sites, this is by far the cheapest. Works well, too. No real complaints here. Could be cheaper if you consider what's in it, though.

Pros: Nice cheap little heatsinks, can be used perfectly for cooling ramchips on your vga. They have a decent stickyness, won't fall off under normal circumstances. But if you want to remove them, it's not very hard.

Cons: None really for that price, it's the same quality and efficiency as the Zalman sinks you get with those expensive vga coolers. Depending on the surface of the chip, zou may need to use additional thermal addhesive if you want a permanent solution.

Other: I can only advise this product, perfect for pushing a little more mhz out of your vga mem! Cost about 1/3 of the branded products and they aren't better. It's aluminium, so copper would cool even better but would also be more expensive. Top product Dealexreme!!

Pros: I've bought thermaltake copper heatsinks for $15 USD and they're basically the same for me so far(not a high-end gamer). These are plenty cheaper and function the same way with an adhesive backing.

Cons: The fins are pretty short, but they still have a decent amount of surface area.

Other: It's a great and cheap alternative to buying thermaltake copper heatsinks when you just need something basic to do the job.