Universal Clamp Mount for Tripods (Holds up to 3.8cm Thick Objects)

Pros: - Unbelievable cheap, for the quality.
- Good quality, no plastic junk, it just really works, the spring doesnt get less powerful or something.
- Universal tripod-screw hole, you can use it on any tripod there is.
- Tiltable
- So much easier to burn things or whatever with your laser, since it focusses easier

Cons: - Doesn't come with a tripod (which is probably a good thing, since else it'll probably be some cheap, poor quality, one)
- Clamp isn't perfectly alligned, one half is like 2mm under the other one, but this doesnt really matter

Other: Get this if you already have a tripod and a laser or something.

Pros: It grabs things, it holds things, and best of all, it holds them still!!!
it is able to grab most of my flashlights no problem, and has a universal tripod screw which makes it easier to use since you can put it on large and small tripods
the squeezing motion allows my laser's button to be pushed while it is being held, which may be good yet bad since it isn't a clicky button like the 200mW red.

Cons: the place where the screw hole is, the bottom metal plate, can be screwed out and sometimes gets stuck to the tripod which makes it pull out a bit while you are unscrewing the tripod.
the plastic is slightly thinner than i had hoped, but that is ok

Other: if you need to hold round stuff still, stop thinking and get this now....

Pros: + Metallic tripod mount (supposed to last) + I can holds everything (from 1.8 to 4.3 cm wide) strong enough to keep it firmly + The strength can be regulated somehow with a screw on the top of the clamp + The tilt angle can be adjusted easily by hand + Suitable for universal tripod

Cons: - Not too much to say except it is made of a bit thin plastic (for the price not a high quality plastic could be expected)

Other: It is a really useful clamp for general purpose. For that price I have ordered two and I am very satisfied with them. Everybody who has a tripod should get one of these clamps at least.

Pros: It does what it is supposed to do, I use it for my laser, and also to hold a flashlight when I work in tight spaces. I have also used it when trying out wireless range with an antenna clasped in it.
I have bolted one to my bike, and it makes an excellent flashlight holder..
I have also used this as a microphone holder.

Cons: As others say, a bit thin plastic, it could also have some kind of rubberised grip. The spring is strong enough, but could not have been much weaker.

Other: Does its job, a bit thin plastic.

Pros: Uses the standard universal screw-down tripod mount. Great for holding lasers and flashlights steady on a tripod. Grip range is wide enough to hold anything from 18650-cell flashlights to pen lasers. A few rubber bands will allow it to hold even smaller things. Good tilt range that's easily adjusted by hand without being too loose. You can also adjust the stiffness with the pivot bolt. Nice, strong spring action.

Cons: Burring on the plastic edges from cheap casting. You may want to sand that off to make it more comfortable to handle. The metal bolt is in direct contact with the plastic of the pivot, which will cause wear and require adjustment after a while. The metal tripod mount insert in the base may come loose eventually for similar reasons.

Other: It's an inexpensive and useful clamp, and it should be a great help to those of you who need a steadier hand to burn things with your lasers.

Pros: - Uses the standard screw tripod mount.
- Great for flashlights, flashlights, microphones and stuff.
- Very cheap.
- Nice colour.
- Very nice..
- And very strong too.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Cons: - Kind thin plastic, some rubberised grip would be handy.

Other: - If you need to hold some round things, this will be great!

Pros: Got this to hold reflectors/diffusers in my shoestring studio for product photography and it's worked great. Was worried that the grip wouldn't be strong enough to hold a 36" panel which can put a lot of pressure on clips such as this with small grip areas but it's worked like a charm so far!

Cons: None, really. It does what it's supposed to.

Other: Tossed this in with an order expecting to be disappointed and I'm glad I got it now!

Pros: - Its cheap
- It fits SKU 1309 so thats actually much better
- Now i can hold my laser steady and burn my matches :P
- It hold on to the items very strong

Cons: - I havent found any yet, but it might not be the best quality.

Other: It will become handy for you in some kind of way. Can be used for alot of stuff. You can build you own laser show with this to hold on you lasers in every direction you want, while loosing your brain to some heavy hardstyle :D Have Fun ...

Pros: -Strong clamp
-Adjustable
-Black and neat looking
-Fits perfectly with the 4 inch tripod available on this site
-Durable
-Smooth black product that's neatly assembled and easy on the eyes

Cons: -None, could be cheaper I suppose.
-Makes a great professional clamp and tripod when combined with the mini tripod.

Other: -Buy it if you need a great small clamp for the 4 inch tripod on this site it's great.

Pros: The clamp is quite strong.
Angle is adjustable.
It's not often that you find something which can be attached to your clamp and be useful.

Cons: Poor build quality. Can tell it's made from inferior plastic.
The plastic clamp might scratch your torch/laser/whatever if you're not careful.

Other: Buy it if you need it. Personally I feel that the cost-value ratio is not very high but when you need something like this, nothing can replace it!